How Do I Repair The Feeder Tray Of A Canon Imageclass Mf5770

Cleaning the Exterior

Make clean the exterior of the machine and ventilation slots.

1. Turn OFF the power switch, and so disconnect the power cord.

two. Make clean the exterior of the machine with a soft, well wrung out cloth dampened with water or a mild detergent that has been diluted with h2o.

3. Await for the auto to dry completely before reconnecting the power cord, and then plough ON the power.

Cleaning the Interior

Make clean the machine's print area periodically to prevent toner powder and paper dust from accumulating inside.

1. Turn OFF the power switch, and then disconnect the power string.

2. Hold the operation panel.

3. Lift the scanning platform.

Note

If yous cannot lift the scanning platform:

• Ensure that the feeder or the platen glass encompass is completely closed. Practise non effort to forcefully lift the scanning platform, equally this may damage the auto.

* If you set thick documents such every bit a book, the the feeder or the platen glass cover may not be completely closed. Remove the documents.

4. Hold the grip on the right or left forepart side of the toner encompass.

For MF4890dw/MF4880dw/MF4770n

For D560/D530

5. Open up the toner cover.

6. Remove the toner cartridge.

7. Remove any toner or paper debris from interior of the machine, with a clean, soft, dry, and lint-free cloth.

8. Insert the toner cartridge.

Fit the protrusions (A) on each side of the toner cartridge into the guides located on each side of the machine. Slide the toner cartridge into the machine, until the toner cartridge meets the back of the machine.

9. Close the toner cover.

Annotation

If you cannot shut the toner embrace:

• Brand sure that the toner cartridge is properly installed in the auto. Do not try to forcefully close the toner cover, as this may damage the machine.

10. Lower the scanning platform.

xi. Connect the power cord, and and then plow ON the power switch.

Cleaning the Fixing Unit of measurement

You should clean the fixing unit when:

• Blackness streaks announced on the output
• You replace the toner cartridge

ane. Press [ ] or [ ] (Menu).

ii. Press [ ] or [ ] to highlight <Adjustment/Maintenance>, then printing [OK].

three. Press [ ] or [ ] to highlight <Clean Fixing Unit of measurement>, and and so press [OK].

4. Check if the supported paper is set up in the multi-purpose tray, and and so press [OK].

The cleaning begins. It takes approximately 90 seconds to consummate the procedure.

* We recommend that y'all load obviously paper when cleaning the fixing unit.

NOTE

If the cleaning does not start:

• Yous cannot use this function when jobs are stored in memory.

v. Press [ ] or [ ] (Menu) to close the Menu screen.

Cleaning the Platen Glass

Follow this procedure to clean the platen glass and the under surface of the the feeder or the platen glass comprehend.

1. Turn OFF the ability switch and disconnect the ability string.

2. Open the the feeder or the platen glass embrace.

3. Clean the platen drinking glass and the under surface of the the feeder or the platen drinking glass cover.

(1)Make clean the areas with a cloth dampened with h2o.

(2)Wipe the areas with a soft, dry cloth.

IMPORTANT

Precautions when cleaning the platen glass:

• Be conscientious non to fold the transparent sheet (A) at the left side of the platen glass.

4. Close the the feeder or the platen drinking glass comprehend.

5. Connect the power cord and plow ON the power switch.

Cleaning the Feeder (MF4890dw/MF4880dw/MF4770n/D560 But)

If your certificate has black streaks or appears dirty after it has been scanned from the feeder, the rollers inside thefeeder may be dirty. Make clean the feeder's scanning expanse and rollers.

one. Plow OFF the power switch, and then disconnect the power string.

ii. Open the feeder comprehend.

3. Clean the rollers (A) within the feeder with a well wrung out material dampened with water and wipe them with a soft, dry out textile.

4. Close the feeder cover.

v. Connect the power string, and and then turn ON the ability switch.

Precautions When Cleaning the Car

Before cleaning the machine, notation the following:

• Make sure that no jobs are stored in memory earlier turning OFF the ability switch and disconnecting the power cord.
• Use a soft cloth to avoid scratching the components.
• Do not clean the machine components with tissue paper, newspaper towels, or similar materials. These materials tend to stick to the components or generate static charges.

Caution

Precautions to accept when cleaning the feeder:

• Practice non dampen the cloth as well much, every bit this may tear the document or impairment the machine.

Precautions to take when endmost the feeder or the platen glass cover:

• Keep your fingers clear of the feeder or the platen glass embrace to avoid injury.

Practise not impact the fixing unit (A).

• Touching the fixing unit (A) may cause burns as information technology becomes very hot during utilise.

Precautions to take when you get toner onto your easily or into article of clothing:

• If toner gets on your hands or clothing, wash them immediately with common cold water.The toner sets onto easily or into clothing if you try to wash it with warm h2o. Once information technology is prepare, you can hardly remove the toner stains.

Of import

Do not touch the transfer roller (A).

• Touching the transfer roller (A) may damage the machine.

Annotation

Sending or receiving faxes (MF4890dw/MF4880dw/MF4770n Merely):

• When the ability plug is unplugged, the machine cannot send or receive faxes.

When a job is waiting to be printed:

• The chore is deleted when y'all plow OFF the ability switch.

Jobs stored in memory (MF4890dw/MF4880dw/MF4770n Only):

• Jobs can exist stored in retentivity for fifty-fifty when the power plug has been unplugged. To view jobs stored in memory,see the following.

How Do I Repair The Feeder Tray Of A Canon Imageclass Mf5770,

Source: https://support.usa.canon.com/kb/index?page=content&id=ART136728

Posted by: smallwoodtheel1940.blogspot.com

Share this post